Wrinkle Plus, Flat Black

Worked well, seems to be durable, color is gloss, no leaks, quality product

VHT is the only automotive paint ill use when it comes to high temp. This specific wrinkle paint works very well if used correctly on a well prepped and clean surface.

This paint was easy to apply and easy to achieve the retro look I desired. The directions are specific, you must read them. It requires a couple coats with a short 5 minute "flash off" dry time between. It was easy to achieve a moderately heavy coat without sags and runs, but, if you have little experience with spray paint, its a good idea to practice before tackling your precious project. A first timer will always have trouble with runs and sags. The nozzle gave me more control than the average rattle can. I give this product a thumbs up. The directions don't really cover oven curing for metal parts. I have plenty of on the job finishing experience so I used our oven to speed up the wrinkling and curing process. Open windows fans help with the paint smell, there will be some paint odor needless to say. After the freshly applied paint coat has air dried (minimum of 30 minutes), This allows the paint solvents to off-gas safely. Its ok for the paint to begin to wrinkle. Then I bake it in the oven at 150 degrees F. for approximately 45 minutes. Since it is a kitchen oven with little venting, I open the oven door briefly every 10 minutes to let remaining gasses escape. Turn the oven off to cool, do not remove the part while still hot. At this point the painted part is cured and durable enough for handling and assembly. Without oven curing you should give the finished part 24 hours before handling. Most plastic parts can't tolerate heat without warping etc.

Good product work very well

This is the best wrinkle finish paint I've ever used. But be advised, this stuff takes FOREVER to gas off. The item I painted almost a week ago is still sitting outside, and still very fragrant. I hope to bring it inside one of these days.

Really good paint only issue I had was my fault I over sprayed and have over hang wrinkle but I was able to shave down the long wrinkles to keep it smooth.

This stuff is awesome! However 2 things to consider 1. How many parts you are spraying cause this stuff doesn't seem to have a lot of paint in the can if you spray it how they recommend (which I do suggest laying it thick as the can says) 2. Def want to bake it in an oven for curing it. I baked it in the house and it def stunk it up not terrible on my opinion but you wouldn't want your kids breathing it in so make sure u can keep the windows open to air the house out. Easy to get rid of the smell. Also I found it very forgiving in laying it on thick meaning it doesn't run/drip easily from what I experienced. Def spray it thick and criss cross pattern as this will allow you to get the best texture possible. It's really sharp looking. Not sure how durable it actually is but seems fairly nice. I wouldn't go dropping it on the ground but seems legit. Color is also more of a flat blue vs shiny which I liked a lot!

As titled; If you do as the can says, the finish is great. Used it in red here on the intake pipe of my r53 . Holds up to engine temps. Finish is great. Just go heavy on the coats after the 1st. Learned that doing a valve cover in black . But alas that's the trick and for prep I just de greased it , then washed it of the chemical residuals, then red Scotch pad it . [Was a polished aluminum to start] Great product for many applications though.

エンジンルームの樹脂製カバーを結晶塗装にしたくなり、某YouTubeで紹介されていたこちらを購入！ 結果的にしっかりと縮み塗装が出来て大満足です！ 結晶塗装特有の縮み感をしっかり出すには、塗装後に即ドライヤーかヒートガンで熱を入れてあげることが大切です！ 夏であれば塗装後に放置して乾燥させるだけで縮むかと思いますが、熱を入れた方が間違いありません。 出来ればドライヤーよりも高温になるヒートガンがおすすめ。 2層目までは薄めに塗り、3〜5層目は少し厚めに塗りました。 都度熱を加えて縮ませながら乾燥しました。 一般的な塗装と違い、熱を入れるという一手間は必要ですが、他にはない結晶塗装がドライヤーだけで出来るというのはとても素晴らしい製品だと思います！ 完全乾燥後は硬さも出てとても綺麗な仕上がりです！

簡単にチヂミ塗装が出来ます。焼かなくて良いのでこれ一択

スプレーして放置しておけば縮みます。 ストーブもヒートガンもいらないので 金属以外にも使用できます。

とにかく簡単に結晶塗装が綺麗にできます。アルミ製のトップブリッジを塗りました。寒い2月でしたが、60度位の湯煎で缶を温めて、脱脂後にミッチャクロンで下地処理、10分置きに3回厚めに塗りました。約24時間程の自然乾燥で触れる位まで乾きますが、塗料が溜まりやすい窪み等はブヨブヨしてます。日当たりの良い場所やストーブの前に放置して毎日確認してましたが完全に硬くなるまで1週間程掛かりました。仕上がりは皺がしっかり入って多少ムラがありますが大満足の質感です。硬化後に強く爪で引っ掻いたりしましたが傷も付かずガチガチです。 その後、メッキのスロットルホルダーも同じ手順と下地処理で、今回は小物なので厚塗り2回で塗りましたが、こちらはさり気ない皺感が良い感じで高級感のある質感になりました。皺感をしっかり出したい大きな物は厚めの3回塗り、小物でさり気ない皺感をねらいたい場合は2回塗りが良いかと思います。完全乾燥にはしっかり時間を取る事をオススメします。

DOHCエンジンの結晶塗装は憧れですが、剥がれ易く再塗装をプロに頼むと高額になるので悩みの種でした。以前の塗料は乾燥時にヒートガン等で熱しないと結晶がうまく出ませんでしたが、本品は夏場でしたら自然乾燥でも大丈夫でした。